1/2 Inch XPS Tile Backer Panels
Lightweight extruded polystyrene (XPS) tile backer boards with reinforced facing for tile installation systems in bathrooms, shower areas, and other suitable interior applications.
Designed for building material importers, distributors, tile accessory wholesalers, and commercial contractors, these panels should be selected according to substrate conditions, tile requirements, waterproofing details, and applicable building regulations.
Request the current Technical Data Sheet (TDS), relevant test reports, installation instructions, and product samples before placing a bulk order.
Designed as a substrate for tile installation systems, with product suitability determined by the complete board construction and approved installation method.
1/2 inch (12.7 mm)
Suitable thickness selection depends on framing conditions, available installation depth, fixture clearances, and the requirements of the specified tile system.
The closed-cell foam core provides a lightweight panel structure. Its thermal and moisture-related properties should be verified against product-specific technical data.
Fiberglass Mesh and Cementitious or Polymer-Modified Coating
The actual facing composition and bonding structure must be confirmed for the supplied product. Adhesive compatibility should be checked against the panel manufacturer's installation instructions.
Potential applications include bathroom walls, shower enclosures, backsplashes, and other suitable interior installations, subject to the product's approved use conditions.
The following table identifies the key procurement parameters. Numerical performance values should be entered only after confirmation against the current product specification and supporting test reports.
|
|
|
|
|
|
|
|
12.7 mm (1/2 inch) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Confirm panel length, width, thickness tolerance, squareness, and edge profile to ensure compatibility with the intended installation layout.
Verify permitted tile materials and sizes, substrate support, fastening patterns, and installation requirements. Panel thickness or core compressive strength alone does not establish allowable tile loads.
Check the compatibility of the finished facing with the specified tile adhesive or mortar. Where ANSI A118.4 or ANSI A118.15 requirements apply, confirm the relevant adhesive classification and the panel manufacturer's installation guidance.
Confirm whether the panel itself has documented waterproofing properties and whether the installation requires joint-sealing tape, sealants, membranes, washers, or other accessories. Pay particular attention to corners, seams, fasteners, and penetrations in wet areas.
Identify the destination market and obtain the applicable product test reports, installation documentation, and regulatory evidence required for the intended application.
Bathroom walls, shower enclosures, commercial backsplashes, and renovation projects may be suitable where the board and complete installation system are specified for those uses.
Floor installations, ceilings, exterior facades, steam rooms, and large-format or thin porcelain tile installations require additional verification against the manufacturer's documented application limits.
Project-Specific Requirements
Confirm framing spacing, substrate condition, fastening methods, tile weight and dimensions, waterproofing details, and applicable local building requirements before installation.
Do not assume that a board suitable for wall applications is automatically suitable for floors, ceilings, or exterior use. Follow the approved installation instructions for the exact product.
Confirm the actual inspection procedures for XPS core materials, facing components, and bonding materials. Record the applicable acceptance criteria where documented.
Verify whether routine inspections cover thickness, panel dimensions, squareness, facing adhesion, and other defined product characteristics.
Request applicable test reports for compressive strength, water absorption, dimensional stability, thermal conductivity, or other required properties. Confirm whether testing is conducted internally or by an independent laboratory.
Confirm the manufacturer's actual lot identification and traceability process, including the availability of production or inspection records when required.
Request the current TDS, installation instructions, applicable Safety Data Sheet (SDS), test reports, and valid quality or compliance certificates where available. ISO 9001 or other certification claims should be made only when supported by current, applicable documentation.
Specify the required length, width, thickness, dimensional tolerances, and quantity. Confirm manufacturing feasibility and minimum order requirements with the supplier.
Square, shiplap, or interlocking edges may be requested where supported by the manufacturer's product range. Confirm profile drawings and compatibility with the intended joint treatment system.
Discuss custom cartons, product labels, barcodes, installation manuals, and pallet markings. Confirm available printing options, artwork requirements, and order quantities before approval.
Request representative panels and relevant technical documents for dimensional checks, facing inspection, adhesive compatibility assessment, and project-specific evaluation.
Finalize drawings, specifications, packaging artwork, and acceptance criteria before mass production.
Confirm the packaging configuration, edge protection, pallet dimensions, stacking limitations, and measures used to prevent handling or transit damage.
Request a loading plan based on panel dimensions, packaging volume, order quantity, and the selected container type. Actual loading capacity depends on the final packing configuration and applicable weight limits.
Confirm the documents required for the destination market and transaction. These may include the commercial invoice, packing list, bill of lading, certificate of origin, and applicable product compliance documents.
Specify the destination port, preferred Incoterm, shipment schedule, and any labeling or import documentation requirements when requesting a quotation.
Q: What is a 1/2 inch XPS tile backer panel used for?
A: A 1/2 inch (12.7 mm) XPS tile backer panel provides a substrate for tile installation in suitable interior applications, including bathroom walls, shower enclosures, and backsplashes. Confirm application suitability and installation requirements in the product documentation.
A: Water resistance depends on the complete panel construction and tested product properties. For shower and other wet-area installations, verify whether the panel forms part of an approved waterproofing system and follow the specified procedures for sealing joints, corners, fasteners, and penetrations.
A: Key parameters include panel dimensions, thickness tolerances, core density, compressive strength, water absorption, facing bond strength, dimensional stability, thermal conductivity, and fire classification.
A: Not necessarily. Compatibility depends on the facing material, adhesive or mortar classification, tile material and dimensions, installation method, and substrate conditions. Confirm the approved adhesive types and tile application limits with the panel manufacturer before specifying the product.
Q: Can 1/2 inch XPS tile backer panels be customized for wholesale orders?
A: Customization may include panel dimensions, thicknesses, edge profiles, private-label packaging, and product labeling, depending on manufacturing capabilities. Buyers should confirm available options, minimum order quantities, sample availability, and production lead times before placing an order.
A: Importers should request the current TDS, installation instructions, applicable performance test reports, relevant compliance documentation, packaging specifications, and sample panels where needed.
To obtain a quotation tailored to your purchasing or project requirements, provide the following information.
Company type, destination country, delivery location or port, and intended distribution or project market.
Required thickness, panel dimensions, edge profile, dimensional tolerances, and any specified technical performance requirements.
Wall, shower, backsplash, or other intended use; substrate type; tile material and dimensions; waterproofing requirements; and applicable installation standards.
Initial trial quantity, estimated recurring orders, annual demand, and preferred packaging configuration.
Required TDS, installation instructions, test reports, compliance documents, and sample evaluation requirements.
Preferred Incoterm, target shipment schedule, labeling requirements, and destination-specific import documentation.
ป้ายกำกับยอดนิยม: 1/2 inch xps tile backer panels, China 1/2 inch xps tile backer panels manufacturers, suppliers, factory

